Digital Watchdog Vmax Ip Plus Login and Password Updated FREE
Digital Watchdog Vmax Ip Plus Login and Password
MEGApix Camera Password Policy and the VMAX IP Plus
MEGApix® Camera Password Policy and the VMAX® IP Plus
-----------------------------------
Affected Roles: Administrator
Complexity: Low to Medium
Firmware Version: VMAX IP Plus v1.iv.i.1
Concluding Edit: November 6, 2020
-----------------------------------
Adding MEGApix® Cameras
In an attempt to increment security, Digital Watchdog'southward MEGApix® cameras at present feature a mandatory password creation when outset connecting with a camera. The VMAX® IP Plus Serial allows users to easily add a camera past just connecting information technology to the NVR'southward PoE (Power-over-Ethernet) switch, simply does non allow users to initially apply a custom password to the camera.
This commodity will outline how to connect a new MEGApix® camera to the VMAX® IP Plus, so how to change the camera's password.
**Notation: For more information regarding changing photographic camera passwords separately from the VMAX® IP Plus, please read Assigning Passwords To IP Cameras .
**NOTE: For more information regarding the different methods for calculation cameras to the VMAX® IP Plus, please read Calculation Cameras To A VMAX IP Plus .
Supported/Affected Devices
- VMAX® IP Plus Serial
- DW MEGApix® Camera Series
Plug n' Play
Past default, when connecting a new MEGApix® IP camera to the born PoE switch of the VMAX® IP Plus unit, the NVR will automatically effort to register the camera to its camera list.
To add a photographic camera using the born PoE switch:
- Connect the camera to the onboard PoE switch (see diagram below) with an Ethernet cablevision.
The camera should power, and so begin to stream video through the NVR afterward it completes the registration process.
- If the photographic camera fails to annals, use the transmission Reset button located inside of the camera housing.
Hold down the Reset push button down for 10 seconds. The photographic camera will reboot and factory default its settings.
The camera should then automatically be added to the NVR.
- If prompted to enter a login for the camera, you may use the following:
- Default ID: admin
- Default Password: admin
Irresolute Camera Passwords Using Virtual Ports
By default, the VMAX® IP Plus is permitted to use the original default login (admin/admin) for the photographic camera afterwards the initial addition to its camera list. However, if a user were to attempt to connect with the photographic camera through the NVR's virtual ports, they would not be able to utilize the camera'southward default login.
To change the camera'south password when connecting through a virtual port:
- Open a web browser on a local figurer.
- Connect with the camera, through the VMAX® IP Plus's virtual port with the following data:
| VMAX ® IP Plus | Virtual Ports |
| Photographic camera Channel – 1 | 18001 |
| Camera Aqueduct – 2 | 18002 |
| Camera Channel – iii | 18003 |
| Photographic camera Channel – 4 | 18004 |
| Camera Aqueduct – 5 | 18005 |
| Photographic camera Channel – half dozen | 18006 |
| Camera Channel – vii | 18007 |
| Camera Channel – 8 | 18008 |
| URL Structure | http://<NVR_IP>:<Virtual_Port> |
Example:
VMAX® IP Plus IP Accost: 192.168.100.51
Camera Connexion: Aqueduct – 3
URL: http://192.168.100.51:18003
- Later on connecting with the camera through the virtual port, you volition be met with a login screen for the camera.
You volition demand the MAC accost of the NVR to go along. This information can be obtained from the Arrangement Information menu of the VMAX® IP Plus.
Log in with the following information:
Username: admin
Password: !A<MAC Address of NVR> (lower instance)
**Note: If the IP camera was registered to the VMAX® IP Plus while the NVR was using firmware version v1.three.7.0 and then updated to version v1.four.1.1, the Password structure will be "!<MAC Address of NVR>". Manufactory reset the camera and motion it to a unlike PoE port or re-add the camera to the organisation to use the updated virtual port password construction of v1.four.1.one.
- To alter the password afterwards logging into the camera, select the System menu, then select User Management.
Select the admin (Administrator), then click Modify.
- Enter the new Countersign.
Enter the new countersign again in the Retype Password field.
Add a Countersign Hint (optional).
Click Apply to save the setting changes.
Digital Watchdog Vmax Ip Plus Login and Password
DOWNLOAD HERE
Source: https://support.digital-watchdog.com/kb/article/343-megapix-camera-password-policy-and-the-vmax-ip-plus/#:~:text=By%20default%2C%20the%20VMAX%C2%AE,addition%20to%20its%20camera%20list.
Posted by: maxwellcritak.blogspot.com